(5-6 mm)
Exposed waterproofing membrane layer as wearing layer
Safety and durability is essential for pedestrian and cycle bridges. Dencryl Bridge Pedestrian bonds with the substrate and provides a sealed wear layer in combination with a flexible, crack-bridging barrier membrane and surface friction suited for walking and cycling. Dencryl Bridge Pedestrian provides a low density option to provide a wear, impact and abrasion resistant surface that will offer corrosion resistance, slip resistance and limited maintenance requirements. It can be used on new bridge construction, routine maintenance or bridge restoration applications. Dencryl Bridge Deck Systems are only installed by authorised and approved applicators.
Will adhere well to dry and clean surfaces including steel and pipe outlets etc.
Will resist rain and snow within 45–60 minutes of installation
Bond of membrane in excess of concrete tensile or cohesive strengths.
Flexibility sufficient to bridge cracks in excess of 3.5 mm in well below freezing conditions.
Very easily repaired if damaged.
Rapid setting and curing enables rapid handover.
Bridges are continuously exposed to severe stresses and typical factors affecting their longevity, include inadequate protection specified at design phase, quality and handling of concrete and/or steel, physical and chemical exposure, climatic conditions, traffic types and frequency and regularity and quality of maintenance. Dencryl Bridge Deck Waterproofing systems provide 100% effective seamless waterproofing thereby denying entry of water, chloride and de-icing salts from permeating into and percolating through the structural concrete deck and thus preventing the steel reinforcement corroding. This also includes corrosion inhibition of orthotropic steel decks etc. where these are the decks of choice.
Roof decks
Pedestrian and cycle bridges
| LAYER | PRODUCT | CONSUMPTION (kg/m²) | INTERMEDIATE | THICKNESS (mm) | APPLICATION |
|---|---|---|---|---|---|
| Primer | Dencryl P11/P12 (Depending on substrate) | 0.3 - 0.5 | Light sand scatter 0.3 - 0.8mm on wet surface | Min 0.3 | Rubber squegee and paint roller |
| Membrane | Dencryl M42 | min 2.8 | None | Min 2.0 | Notched rubber squegee |
| Wear layer | Dencryl M42 + aggregate | min 2.8 + aggregate | broadcast | Min 3.0 | Notched rubber squegee |
| Topcoat | Dencryl S31 | 0.7 -1.2 | None | 0.5 - 0.8 | Rubber squegee and paint roller |
Properties
Value
Fully cured at 20°C
2 hours
Applied thickness
5 - 6 mm
Water Permeability
Nil – Karsten test (impermeable)
Hardness
SHORE D 80
Compressive strength
85 MPa
Reaction to fire
Dfl-s1
Bond strength
>1.5 MPa
Temperature resistance
Up to 80°C at 4 mm
Thermal expansion coefficient
<40 ppm
Abrasion resistance
50 mg / 1000 cycles (Taber Abrader)
Thermal conductivity
< 0,4 W/m·K
Anti-slip according to DIN 51130
R9 – R13
Dencoat India
2026-02-11
Dencoat India, a leading player in building materials and surface coatings, has just introduced a new type of waterproofing membrane that promises to redefine standards for moisture and water intrusio...
READ MORE
Nordzucker, Denmark
Dencoat Danmark
2026-02-11
Being one of two sugar factories in Denmark, Nordsucker Nakskov was once the largest sugar factory in Northern Europe. Built in1882, it could process 300 tonnes of sugar beet per day. This made the f...
READ MORE
Diesel Technic, Dubai
Dencoat India
2025-02-28
DUBAI, EMIRATES OF DUBAI, UNITED ARAB EMIRATES, February 20, 2025 Duphill Technical Solutions LLC has successfully completed the flooring project for Diesel Technic’s cutting-edge warehousing f...
READ MORE
